Handling and Installation Best Practices for Glass Processing
Why Handling Matters More for Insulated and Dynamic Glazing
An insulated glass unit is a sealed system, not a single pane. Industry guidance on IGU handling and installation is direct about the consequences of getting it wrong: incorrect installation can significantly shorten a unit’s lifespan, and can void the manufacturer’s warranty against seal failure. Dynamic glazing units carry the same sealed-cavity handling requirements as standard IGUs, plus an electrical layer that adds its own handling considerations.
Receiving and Storage
Standard IGU guidance from the Insulating Glass Manufacturers Alliance (IGMA) covers receiving, storage, and glass protection as its own dedicated section, not an afterthought. The general principles carry over directly to dynamic glazing:
- Store units vertically on properly padded A-frames or racks, never flat, to avoid uneven pressure on the seal
- Keep units in original packaging until just before installation to protect against dust, moisture, and edge damage
- Avoid direct sun exposure or extreme temperature swings during storage, which stresses both the glazing seal and any electrical components inside the unit
- Avoid all edge impacts during transport and installation. Even minor chips or shelling at the glass edge can significantly reduce glass strength and increase the risk of later breakage.Edge Protection
Moving and Lifting Large-Format Units
Large-format glazing introduces handling risks that don’t show up with smaller panels. Industry guidance on large IGUs notes that framing members need to properly support and retain the unit’s full weight, and that setting blocks must be sized and positioned correctly to bear that weight without causing excessive deflection, which can lead to water pooling and, eventually, glass damage.
For large-format units, vacuum lifting equipment appropriately rated for the panel’s weight, size, and configuration is generally recommended and widely used in the industry. This matters more, not less, for dynamic glazing, since an uneven lift that stresses the glass also risks the electrical layer bonded within it.
Setting Blocks, Clearances, and Glazing System Compatibility
Framing systems designed around single-pane glazing often need modification before they’re suitable for IGUs, since the sealed airspace and perimeter seal need consistent support the original frame design may not have accounted for. Before installation begins, it’s worth confirming:
- Setting blocks are the correct width and thickness for the unit’s actual thickness, not a generic size carried over from a previous job
- Glazing clearances match the unit’s manufacturer specifications, not just the opening’s existing dimensions
- Sealants and spacer materials in the glazing system are chemically compatible with the IGU’s own seal materials, incompatible combinations can compromise the seal over time
- Ensure the glazing system provides proper drainage and ventilation where required. Standing water in contact with the edge seal can significantly reduce IGU service life.
Electrical Connection and Testing Before Final Glazing
This step is specific to dynamic glazing and isn’t covered by general IGU handling standards. Cables, connectors, and pigtails should be protected from moisture, UV exposure, pinching, and mechanical damage during storage and installation. Before a unit is fully set into its final frame, it’s good practice to test the electrical connection and confirm the glazing switches correctly. Catching a wiring or connection issue while the unit is still accessible is far easier than discovering it after the glazing system is fully sealed and trimmed out.
Common Installation Mistakes to Avoid
- Verify correct glass orientation and connection location according to the manufacturer’s installation drawings and Sticker before final placement.
- Undersized or misplaced setting blocks, which can cause the unit to settle unevenly and stress the seal over time
- Excessive sill deflection, which allows water to pool at the center of a large unit instead of draining properly
- Incompatible sealants, gunned-in-place glazing materials that weren’t checked against the IGU’s own seal chemistry
- Skipping the pre-install electrical test on dynamic glazing, leaving a wiring issue to be discovered only after the unit is sealed into place
FAQ
Does installing dynamic glazing require different handling than a standard IGU? The core handling principles, storage, lifting, setting blocks, and clearances, are the same as any sealed IGU. The difference is the added electrical connection, which should be tested before the unit goes into its final frame, a step standard IGU installation doesn’t require.
What happens if an IGU is installed incorrectly? Incorrect installation can shorten the unit’s expected lifespan and may void the manufacturer’s warranty against seal failure, since most warranties assume the glazing system was installed according to specification.
Do large-format dynamic glazing panels need special lifting equipment? Yes, for the larger panel sizes now common in architectural and automotive glazing, vacuum lifting equipment rated for the panel’s specific weight and dimensions is standard practice rather than optional.
Should the electrical connection be tested before or after the unit is fully glazed? Before. Testing the connection while the unit is still accessible makes it far easier to catch and fix an issue than after the glazing system is sealed and trimmed.
Talk to eLstar Dynamics About Your Process
If you’re setting up handling and installation procedures for ELM glazing, get in touch with eLstar Dynamics, or visit our Glass Processors page for more on integrating ELM into your production line, or our Technology page to see how ELM works.